Dimming inserts

Touch dimmer Standard LED

You can switch and dim your lighting with the touch dimmer Standard LED. As an LED dimmer, the dimmer specifically sets itself automatically to leading edge or trailing edge phase control. The dimmer is implemented as 2-wire / 3-wire device and is supplied with 230 V mains power.

Therefore, operation without neutral conductor is also possible. Using the mode selector push-button with LED indication, you can conveniently configure the dimmer. The standard touch dimmer can be installed in a commercially available device socket (e.g. Kaiser 1055-02) according to DIN 49073.

  • 230 V AC ~, 50/60 Hz
  • Connection: screw terminals
  • Connected load: diverse; see product data sheet
  • Number satellite inserts 3-wire (reference number 1723 NE): no connection of satellite units possible
  • Number of push-buttons: no connection of satellite units possible
  • Display of the set operating mode with LED
  • Covers: .. 17180 .. / .. 17280 .. / .. 17181 .. / .. 17281 .. / .. DWPM 17360 ..
  • Automatic or manual setting of the dimming principle applicable for the load
  • Switching on uses a soft start that is gentle on the lamp
  • Switching on with the last set brightness or with the saved switch-on brightness
  • Switch-on brightness can be permanently stored
  • Electronic short-circuit protection with permanent switch-off after 7 seconds at the latest
  • Electronic overtemperature protection
  • The device uses the leading edge phase control or trailing edge phase control principle
  • Device can also be operated without neutral conductor
  • Total length of power cable: 100 m
  • Total length of satellite cable: no connection of satellite units possible
  • Capacity expansion possible using power boosters.
  • Minimum brightness can be saved permanently
  • Stand-by power: approx. 0.25 W
  • Test operation to check function
  • Ambient temperature: –5 ... +45 °C
  • Power loss: approx. 2 W

You can find more information here: qr.jung.de/ean/4011377166905

Touch dimmer Universal LED

You can switch and dim your lighting with the touch dimmer Universal LED. As an LED dimmer, you can configure the touch dimmer Universal LED specifically as leading edge phase control or trailing edge phase control. The touch dimmer is implemented as a 2-wire / 3-wire device and is supplied with 230 V mains voltage. Therefore, operation without neutral conductor is also possible. It has a satellite input for the satellite unit 2-wire/3-wire as well as a push-button.

Using the mode selector push-button with LED indication, configuring the touch dimmer is convenient. The touch dimmer Universal LED can be installed in a commercially available wall box (e.g. Kaiser 1055-02) according to DIN 49073.

  • 230 V AC ~, 50/60 Hz
  • Connection: screw terminals
  • Connected load: diverse; see product data sheet
  • Number of satellite inserts 3-wire (reference number 1723 NE): 5
  • Number of push-buttons: unlimited
  • Display of the set operating mode with LED
  • Covers: .. 17180 .. / .. 17280 .. / .. 17181 .. / .. 17281 .. / .. DWPM 17360 ..
  • Automatic or manual setting of the dimming principle applicable for the load
  • Switching on uses a soft start that is gentle on the lamp
  • Switching on with the last set brightness or with the saved switch-on brightness
  • Switch-on brightness can be permanently stored
  • Electronic short-circuit protection with permanent switch-off after 7 seconds at the latest
  • Electronic overtemperature protection
  • The device uses the leading edge phase control or trailing edge phase control principle
  • Device can also be operated without neutral conductor
  • Total length of power cable: 100 m
  • Total length of satellite cable: 100 m
  • Capacity expansion possible using power boosters.
  • Minimum brightness can be saved permanently
  • Stand-by power: approx. 0.25 W
  • Test operation to check function
  • Ambient temperature: –5 ... +45 °C
  • Power loss: approx. 4 W

You can find more information here: qr.jung.de/ean/4011377166912

Rotary dimmer LED with 2-way push switch

With the LED rotary dimmer with 2-way push switch you can switch and dim your lighting in trailing edge phase control. Operation is with a suitable centre plate.

The touch dimmer Universal LED can be installed in a commercially available wall box (e.g. Kaiser 1055-02) according to DIN 49073.

Connection and functions

  • 230 V AC ~, 50/60 Hz
  • Loosening torque of the connection: max. 0.5 Nm
  • Installation depth: 24 mm
  • Switching on uses a soft start that is gentle on the lamp
  • Electronic short-circuit protection
  • Electronic overtemperature protection
  • The device operates according to the trailing edge phase control principle
  • Total length power cable: max. 100 m
  • Reduction of load
    • For every 5 °C exceeding 35 °C: -10 %
    • When installed in wooden or hollow walls: -15 %
    • When installed in multiple combinations: -20 %
  • Maximum and minimum brightness adjustable and can be permanently saved
  • Stand-by power: none
  • Ambient temperature: 0 ... +35 °C
  • Power loss: max. 2 W

You can find more information here: qr.jung.de/ean/4011377360556